Menu
Logo

Fujitsu Siemens S300: Hardware 


 


 

 



Fujitsu Siemens Futro S300 Thin Client

The Fujitsu Siemens S300 is essentially identical to the S200. It is one of the larger thin clients around. It's neatly packaged and, although not as power hungry as the s400, does carry the same warning label about using it vertically with a stand.

A datasheet I found on the S300 is dated October 2005.

When a cheap one appeared on eBay a quick search indicated to me that this was actually the same as an S200. Photographs showed the same motherboard (TR5670). However the datasheet did claim as far as the network was concerned:

LAN on board10/100/1000 Mbit/s
Fast Ethernet   Connectivity TP (Twisted Pair), RJ-45

The claim of gigabit ethernet implied a difference in specification. I should have paid attention to the line below which said 'fast ethernet' (ie 100Mbit/s) as that's all I found.

Specifications

The basic specs for the S300 are:

Processor
   Type
   Speed
Transmeta TM5800
800MHz
Memory

   Compact Flash
   RAM
eLux
128MB, 256MB
128MB, 256MB, 512MB
XPe
256MB, 512MB
256MB, 512MB
Video
   Chip
   Max resolution
   Connector
SiS315
32 bit colors, 1600 x 1200 / 85 Hz
VGA
Ports
   Network
   USB
   Serial
   Parallel
   PS/2
10/100
4 x USB2.0
1
1
Kybd & mouse
Power
   Power
   Plug
   Off
   Idle
   Running
100-240V 50/60Hz
IEC
2W
13W
16W
Dimensions
H x W x D (mm)246 x 48 x 177

My S300 came with eLux NG as the operating system and 128MB/256MB of Flash/RAM.

Power Supply

The S300 has an internal power supply and uses a standard IEC connector.

CPU

The S300 is fitted with a Transmeta Crusoe clocked at 800MHz.

The Linux cpuinfo reports:

vendor_id:GenuineTMx86
cpu family:5
model:4
model name:Transmeta(tm) Crusoe(tm) Processor TM5800
stepping:3
flags:fpu vme de pse tsc msr cx8 sep cmov mmx longrun lrti constant_tsc

PCI

The output from Linux's lspci command:

00:00.0 Host bridge: Transmeta Corporation LongRun Northbridge (rev 03)
00:00.1 RAM memory: Transmeta Corporation SDRAM controller
00:00.2 RAM memory: Transmeta Corporation BIOS scratchpad
00:09.0 VGA compatible controller: Silicon Integrated Systems [SiS] 315PRO PCI/AGP VGA Display Adapter
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)

DisassemblyFutro S300 circuit board

This is fairly straight forward. First remove the two screws that hold on the front cover. The front cover can then be gently slid forward. I found it to be a snug fit and it needed a bit of gentle encouragement to move. Next remove the two screws on the rear that hold on the top cover. This can then be removed.

Motherboard

The motherboard is labelled as a TR5670 Rev 1.4. Click on the photograph to get a more detailed view of the circuit board.

Expansion

Flash: The board is fitted with an Compact Flash socket so increasing the size of the flash is easy. There is also a 40-pin IDE socket. I haven't yet experimented with that.

RAM: The board has a single SODIMM socket for DDR memory. Mine came fitted with a PC2700S 256MB part - HYS64D32020HDL. A 512MB part worked (Kingston KFJ-FPC50/512 2.5V). I believe the integrated northbridge of the TM5800 will only support up to 512MB of DDR RAM.

PCI: There is a PCI socket. My S300 came fitted with a riser card.

Ethernet: Despite the mention of 10/100/1000 Mbit/s on the datasheet the S300, like the S200, is fitted with a VIA VT6102 that only supports Fast Ethernet (100MBits/s) speeds.

Futro S300 jumper 7 Auto Boot: There is a jumper (JP7) adjacent to the buzzer that governs whether the S300 automatically boots on power-up or waits until the front button is pressed.

Futro S300 USB socket USB: There are two USB 2.0 sockets on the front and two on the rear. There are also (maybe) two internal USB sockets. There is a connector (J4) near the PCI socket. I plugged in a standard motherboard-to-two-USB sockets cable and checking with a pen drive found I had one more active USB port. My guess is the other one works as well but for some reason Fujitsu-Siemens opted to leave off the +5V pin, so anything - such as a pen drive - that relies on being powered from the socket, will not work.

 


Any comments? email me. Added May 2015    Last update May 2015